Voltage divider calculator
Enter the input voltage and the two resistors to get the output voltage across R2, the current through the pair and the power each resistor turns into heat. Type resistances the way they are printed on the bag: 470, 10k, 4k7 or 2.2M.
Example: Vout = 3.837 V
12 V across 10 kΩ over 4.7 kΩ leaves 3.837 V at the middle, 31.97% of the input. The pair draws 0.816 mA.
| Output voltage (across R2) | 3.837 V |
|---|---|
| Voltage across R1 | 8.163 V |
| Divider ratio, R2 ÷ (R1 + R2) | 0.3197 |
| Total resistance | 14.7 kΩ |
| Current | 0.816 mA |
| Power in R1 | 6.664 mW |
| Power in R2 | 3.132 mW |
Worked from the formula shown for low-voltage DC circuits. Part values vary within their tolerance, so confirm with a multimeter and the parts' datasheets before you rely on a figure.
This is the unloaded output. Anything connected to the output draws current through R1 as well and pulls the voltage down.
The formula, with a worked example
- Output voltage: Vout = Vin × R2 ÷ (R1 + R2), where R1 runs from the input to the output and R2 from the output to ground.
- Current through both resistors: I = Vin ÷ (R1 + R2).
- Power in each resistor: P = I² × R.
- Worked example: 12 V across R1 = 10 kΩ and R2 = 4.7 kΩ. Together they make 14.7 kΩ, so Vout = 12 × 4,700 ÷ 14,700 = 3.837 V.
- The current is 12 ÷ 14,700 = 0.816 mA, so R1 dissipates 0.000816² × 10,000 = 6.66 mW and R2 dissipates 3.13 mW.
- To hit a target, rearrange for R2: R2 = R1 × Vout ÷ (Vin − Vout). For 3.3 V from 5 V with R1 = 10 kΩ, R2 = 19.4 kΩ; the nearest E24 value, 20 kΩ, gives 3.33 V.
How two resistors split a voltage
Two resistors in series carry the same current, so each one drops a share of the input in proportion to its resistance. R2 takes R2 ÷ (R1 + R2) of the total. Equal resistors split the input in half, and making R2 three times R1 gives three quarters of the input at the middle point.
Only the ratio sets the output. A 1 kΩ and 2 kΩ pair gives the same voltage as 100 kΩ and 200 kΩ. What changes with the size is the current the pair wastes and how easily the output is pulled around by whatever is connected to it.
Why the measured output is lower than calculated
The formula assumes nothing is connected to the output. Anything you attach sits in parallel with R2 and lowers the effective bottom resistance, so the output drops. A rule of thumb is to keep the load at least ten times the resistance of R2; at that ratio the error is under ten percent, and at a hundred times it is under one.
Your multimeter is a load too. A typical digital meter has about 10 MΩ of input resistance, which hardly matters with 10 kΩ resistors but noticeably drags down a divider built from megohm parts. If a high-value divider reads low, the meter may be the reason.
Tolerance adds a second error. Two 5% resistors can land at opposite ends of their windows, which shifts the ratio by a few percent. Where the output voltage matters, 1% parts are cheap and worth it.
Choosing the resistor values
Start from the current you can afford to waste. Battery projects favour 100 kΩ and up so the divider draws only microamps. Circuits that feed an analog-to-digital converter usually want a lower source resistance, often 10 kΩ or less, because the converter samples through a small capacitor that needs charging quickly.
Check the power figure too. With small signals it is a few milliwatts, far inside any quarter-watt part, but a low-value divider across a 24 V rail can turn a surprising amount of energy into heat. The calculator shows the watts in each resistor so you can compare them with the part rating.
Where dividers are used
Typical jobs are scaling a battery voltage down to a microcontroller input, setting the feedback voltage of an adjustable regulator, biasing a transistor, reading a potentiometer or a thermistor, and shifting a 5 V logic signal down to 3.3 V for a slow input.
A potentiometer is a divider in one package: the wiper splits a fixed track into R1 and R2, so turning it slides the output from zero to the full input.
When a divider is the wrong tool
Do not use a divider to power anything. A motor, a module or a string of LEDs draws a current that changes, and the output voltage swings with it. A linear regulator or a buck converter holds its output steady whatever the load does; a divider cannot.
For fast logic signals the divider resistors and the input capacitance of the receiving chip form a filter that rounds off the edges. Above a few hundred kilohertz a proper level-shifter chip does a cleaner job.
Common divider pairs
| Input | R1 | R2 | Output | Current |
|---|---|---|---|---|
| 5 V | 10 kΩ | 20 kΩ | 3.333 V | 0.167 mA |
| 5 V | 1.8 kΩ | 3.3 kΩ | 3.235 V | 0.98 mA |
| 5 V | 10 kΩ | 10 kΩ | 2.5 V | 0.25 mA |
| 3.3 V | 10 kΩ | 10 kΩ | 1.65 V | 0.165 mA |
| 9 V | 10 kΩ | 10 kΩ | 4.5 V | 0.45 mA |
| 12 V | 15 kΩ | 10 kΩ | 4.8 V | 0.48 mA |
| 12 V | 10 kΩ | 4.7 kΩ | 3.837 V | 0.816 mA |
| 24 V | 47 kΩ | 10 kΩ | 4.211 V | 0.421 mA |
Frequently asked questions
How do I get 3.3 V from 5 V with two resistors?
Use R2 about twice R1. A 10 kΩ top resistor with a 20 kΩ bottom one gives 5 × 20 ÷ 30 = 3.33 V. With E12 parts, 1.8 kΩ over 3.3 kΩ gives 3.24 V.
Which resistors divide 12 V down to 5 V?
You need R1 = 1.4 × R2. A 14 kΩ top resistor (an E96 value) over 10 kΩ gives exactly 5 V. With common parts, 15 kΩ over 10 kΩ gives 4.8 V.
What is the divider ratio?
R2 ÷ (R1 + R2), the fraction of the input that appears at the output. Multiply the input voltage by it to get Vout. The example on this page has a ratio of 0.3197.
Can a voltage divider power a circuit?
Not reliably. The output only holds while the load is far larger than R2. Any device that draws real current drags the voltage down, and the resistors waste power the whole time. Use a regulator for supplies and a divider for signals.
Does the formula work for AC signals?
For plain resistors, yes: the ratio is the same for a low-voltage audio or sensor signal. Add a capacitor to the mix and the answer starts to depend on frequency, which this calculator does not cover.
Why does my divider read a lower voltage than this page shows?
Something is loading the output. That can be the circuit it feeds, a leaky capacitor, or the meter itself on a high-value divider. Measure with the load disconnected to compare against the calculated figure.
Driving an LED instead? Find the series resistor, the current you will get and the power rating it needs with the LED resistor calculator.
Other calculators on this site
-
Resistor color code calculator
Read 4, 5 and 6-band resistors: value, tolerance and the range a meter should show.
-
LED resistor calculator
The series resistor for one LED or a string, rounded to a stock value, with its power rating.
-
Parallel and series resistor calculator
Total resistance of two to six resistors in parallel and in series, with each one's current and power.
-
Ohm's law calculator
Enter any two of voltage, current, resistance and power to get the other two.
-
Resistor voltage drop calculator
The voltage across a resistor from the current, or from the supply and the rest of the circuit.
-
SMD resistor code calculator
Decode 3-digit, 4-digit, R and EIA-96 codes on surface-mount resistors.
-
RC time constant calculator
τ = RC, the capacitor voltage at each time constant, and the filter cutoff.