Skip to content
Resistor Math

Parallel and series resistor calculator

Type two to six resistances and the calculator adds them up both ways: the total when they are wired end to end in series, and the total when they sit side by side in parallel. Add the voltage across the group to see how the current and the heat divide between the parts.

Optional.

Optional.

Optional.

Optional.

Optional. Shows the current and power in each part.

Example: parallel 3.197 kΩ, series 14.7 kΩ

10 kΩ, 4.7 kΩ make 3.197 kΩ side by side in parallel and 14.7 kΩ end to end in series. On 12 V the parallel group draws 3.753 mA and the series string 0.816 mA.

Resistor Share of current in parallel Parallel: current Parallel: power Series: voltage Series: power
10 kΩ 32% 1.2 mA 14.4 mW 8.163 V 6.664 mW
4.7 kΩ 68% 2.553 mA 30.638 mW 3.837 V 3.132 mW

Worked from the formula shown for low-voltage DC circuits. Part values vary within their tolerance, so confirm with a multimeter and the parts' datasheets before you rely on a figure.

A combination keeps the tolerance of its parts: two 5% resistors give a total that can sit up to 5% from the figure above. Measure the finished combination if the exact value matters.

The formula, with a worked example

Series: one path, so the resistances add

Resistors in series sit one after another, so every bit of current that passes through the first has to pass through the rest. The current is the same in each part, and the supply voltage is shared out in proportion to resistance: the largest resistor takes the largest slice.

Series is the easy way to build a value you do not have. A 1 kΩ and a 470 Ω part make 1.47 kΩ, and two 10 kΩ parts make 20 kΩ. It is also a way to spread heat: three equal resistors in series each take a third of the voltage and a third of the power.

Parallel: more paths, less resistance

In parallel every resistor connects across the same two points, so each one sees the full voltage and draws its own current. More paths mean more total current for the same voltage, which is another way of saying the combined resistance falls. Adding any resistor in parallel, however large, lowers the total.

Equal resistors make the arithmetic easy: n identical parts in parallel give one nth of the value. Two 1 kΩ parts give 500 Ω, and four 10 kΩ parts give 2.5 kΩ. When one part is ten times the other, the total is only about nine percent below the smaller one, so the large part barely matters.

The current divides the opposite way to the voltage in a series string: the smallest resistor takes the largest share. The percentage column in the result shows each part's share of the total current.

Making an odd value from stock parts

Kits come in E12 or E24 steps, so a calculated value such as 3.4 kΩ or 75 Ω may not be in the drawer. Two parts in series reach values above the larger part; two in parallel reach values below the smaller one. 3.3 kΩ in series with 100 Ω gives 3.4 kΩ, and 100 Ω in parallel with 300 Ω gives exactly 75 Ω.

Combining parts tends to tighten the tolerance a little on average, because random errors partly cancel. It does not improve the worst case, though: if every part sits at the top of its window, so does the total.

Sharing power between resistors

Every resistor has a power rating, and a single small part may be too weak for the job. Two equal resistors in parallel, each twice the value you need, share the heat evenly, so two 1/4 W parts can stand in for one 1/2 W part. The same trick works in series with two parts at half the value each.

Unequal parts do not share evenly. In parallel the smaller resistor runs hotter, and in series the larger one does. Enter the voltage to see the watts in each part, then compare every figure with that part's own rating.

Mixed networks: work from the inside out

Real circuits often mix the two, such as two resistors in parallel followed by a third in series. Reduce the network one group at a time: work out the parallel pair first, then add the series part to that result. Run this calculator once per group and carry each answer forward.

Check the answer against common sense. A parallel total must be smaller than the smallest part in its group, and a series total must be larger than the largest. If a figure breaks either rule, a value was typed wrong or the groups were combined in the wrong order.

Common combinations in parallel and in series

Resistors In parallel In series
1 kΩ + 1 kΩ 500 Ω 2 kΩ
10 kΩ + 10 kΩ 5 kΩ 20 kΩ
4.7 kΩ + 4.7 kΩ 2.35 kΩ 9.4 kΩ
1 kΩ + 2.2 kΩ 687.5 Ω 3.2 kΩ
470 Ω + 1 kΩ 319.728 Ω 1.47 kΩ
10 kΩ + 4.7 kΩ 3.197 kΩ 14.7 kΩ
330 Ω + 680 Ω 222.178 Ω 1.01 kΩ
100 Ω + 300 Ω 75 Ω 400 Ω
220 Ω + 220 Ω + 220 Ω 73.333 Ω 660 Ω
100 Ω + 220 Ω + 470 Ω 59.977 Ω 790 Ω
10 kΩ + 10 kΩ + 10 kΩ + 10 kΩ 2.5 kΩ 40 kΩ

Parallel totals rounded to three decimals of the unit shown.

Frequently asked questions

What is 10k and 10k in parallel?

Five kilohms. Two equal resistors in parallel always give half the value of one, because each carries half of the total current.

How do I calculate two resistors in parallel?

Multiply them and divide by their sum. For 1 kΩ and 2.2 kΩ that is 2,200,000 ÷ 3,200 = 687.5 Ω.

Is the total in parallel always less than the smallest resistor?

Yes. Every extra path lets more current flow at the same voltage, so the combination always comes out below the smallest single part, by however little.

How many resistors can I add here?

Up to six. For a bigger group, work out the first six, then enter that total as one resistor alongside the rest. The final answer comes out the same.

Do resistors in series carry the same current?

They do. There is only one path, so the current is identical in every part. The voltage is what divides, in proportion to each resistance.

Why does my meter read a different total from the calculator?

Each part can be off by its tolerance, and an in-circuit reading includes anything else connected across the same two points. Lift one end of the network out of the circuit and measure again.

Need the voltage, current or power for a single resistor instead? Fill in any two of them in the Ohm's law calculator.

Other calculators on this site