SMD resistor code calculator
Type the number printed on top of a surface-mount resistor, exactly as you see it. The calculator works out which code system it uses, reads the value, gives the tolerance that system usually goes with, and shows how the same value would be written in the other systems.
Example: 103 = 10 kΩ
Read as a 3-digit code, which usually means a ±5% part.
| Resistance | 10 kΩ (10,000 Ω) |
|---|---|
| Code system | 3-digit code |
| Usual tolerance | ±5% (not carried in the code) |
| As a 3-digit code | 103 |
| As a 4-digit code | 1002 |
| As an EIA-96 code | 01C |
| Standard series | E6, E12, E24, E96 |
Worked from the formula shown for low-voltage DC circuits. Part values vary within their tolerance, so confirm with a multimeter and the parts' datasheets before you rely on a figure.
Makers do not all follow the same marking rules, and very small parts (0402 and below) are often left unmarked. A code read upside down can give a different value, so measure the part with it out of the circuit if the reading matters.
The formula, with a worked example
- 3-digit code: the first two digits are the value and the third is the number of zeros after them. 103 is 10 followed by three zeros, 10,000 Ω or 10 kΩ.
- 4-digit code: three value digits and then the number of zeros. 1002 is 100 followed by two zeros, again 10 kΩ, and 4991 is 4,990 Ω.
- R as the decimal point: 4R7 is 4.7 Ω, R47 is 0.47 Ω and 10R0 is 10 Ω. Codes with an R have no multiplier digit.
- EIA-96 code: two digits pick a value from the E96 series (01 = 100, 02 = 102 and so on up to 96 = 976), and a letter multiplies it. 01C is 100 × 100 = 10 kΩ, and 68C is 499 × 100 = 49.9 kΩ.
- Multiplier letters: Z × 0.001, Y × 0.01, X or S × 0.1, A × 1, B or H × 10, C × 100, D × 1,000, E × 10,000 and F × 100,000.
- A code of all zeros (0, 00, 000 or 0000) marks a zero-ohm jumper, a link that stands in for a wire.
Why chips use numbers instead of bands
Surface-mount resistors are flat blocks a millimetre or two long, too small for painted stripes. Instead the value is printed or laser-marked on top as a short code. Through-hole parts and chips follow the same preferred-value series, so a 4.7 kΩ chip and a 4.7 kΩ banded part are the same resistance, just labelled differently.
The size is named by its footprint in hundredths of an inch: 1206 is 0.12 by 0.06 inches, 0805 and 0603 are smaller again. The larger sizes carry a full code, and the tiny 0402 and 0201 parts usually carry nothing at all, so the reel label is the only record of their value.
Telling the code systems apart
Three digits with no letters is the older system for 5% parts. Four digits points to a 1% part from a wider series that needs three significant figures. Two digits followed by a letter is EIA-96, a compact way of fitting a three-figure 1% value into three characters on the smallest marked chips.
An R anywhere in the code is the decimal point and appears on values below 10 Ω or 100 Ω, where a multiplier digit would be awkward. This calculator always reads R as a decimal point, never as an EIA-96 letter, so 10R is 10 Ω. A code that fits no system gets an error rather than a guess.
Reading the multiplier
The last digit of a 3-digit or 4-digit code counts zeros, so it is easy to read one too many or too few. 472 is 47 with two zeros, 4,700 Ω, not 472 Ω. A final 0 means no zeros: 220 is plain 22 Ω and 1000 is 100 Ω. This calculator reads multiplier digits from 0 to 7; a code ending in 8 or 9 is not a usual resistor marking, so it asks you to check the code.
EIA-96 letters work the same way but as a lookup. Z, Y and X push the value below 100 Ω, A leaves it at 100 to 976 Ω, and each letter after that adds a zero. The table below the calculator shows common values in all three systems side by side, so you can match a reel label to the code on the part.
Tolerance, and what the code does not say
None of these codes carries a tolerance. The system only hints at it: 3-digit parts are usually 5%, while 4-digit and EIA-96 parts are usually 1% because their values come from the finer E96 series. Some makers put a bar under the code or use a slightly different layout for tighter parts, and their datasheet is the only way to be sure.
Power rating is not in the code either. It follows the size, from about 1/16 W for an 0402 to about 1/4 W for a 1206, but makers differ and some offer higher-power versions in the same footprint. Look up the series on the reel or the bill of materials before relying on a figure.
Checking a part on the board
Reading the code upside down is a common slip: 601 read the other way can look like 109, and a misread code may still decode to a plausible value. If the result surprises you, turn the board round and try again, and compare it with neighbouring parts that should match.
Measuring in circuit gives a low reading whenever other parts sit in parallel with the one you are testing. For a firm answer, lift one end with a soldering iron or measure a spare from the same reel. With the power off, a meter on the ohms range settles any doubt in a few seconds.
Common SMD resistor codes
| Value | 3-digit | 4-digit | EIA-96 |
|---|---|---|---|
| 0.47 Ω | R47 | R470 | — |
| 1 Ω | 1R0 | 1R00 | 01Y |
| 4.7 Ω | 4R7 | 4R70 | — |
| 10 Ω | 100 | 10R0 | 01X |
| 47 Ω | 470 | 47R0 | — |
| 100 Ω | 101 | 1000 | 01A |
| 220 Ω | 221 | 2200 | — |
| 330 Ω | 331 | 3300 | — |
| 470 Ω | 471 | 4700 | — |
| 1 kΩ | 102 | 1001 | 01B |
| 2.2 kΩ | 222 | 2201 | — |
| 4.7 kΩ | 472 | 4701 | — |
| 4.99 kΩ | — | 4991 | 68B |
| 10 kΩ | 103 | 1002 | 01C |
| 47 kΩ | 473 | 4702 | — |
| 100 kΩ | 104 | 1003 | 01D |
| 1 MΩ | 105 | 1004 | 01E |
A dash means the value has no code in that system: 4.99 kΩ needs three digits, and only E96 values have an EIA-96 code.
Frequently asked questions
What resistor is 103?
10 kΩ. The digits 1 and 0 are followed by three zeros, giving 10,000 Ω.
What does 4R7 mean on a resistor?
4.7 Ω. The R stands in for the decimal point.
What is 01C on an SMD resistor?
It is an EIA-96 code for 10 kΩ. Code 01 is the E96 value 100, and C multiplies by 100.
What does 000 mean on a resistor?
It is a zero-ohm jumper, a part that links two pads like a piece of wire.
How do I read a 4-digit SMD code?
Take the first three digits as the value and the last as the number of zeros. 4701 is 470 followed by one zero, 4,700 Ω.
Why is my SMD resistor not marked?
Sizes of 0402 and smaller usually have no room for a code. Measure the part or check the reel label and the board documentation.
Pairing a resistor with a capacitor for a delay, a debounce or a simple filter? Work out its timing with the RC time constant calculator.
Other calculators on this site
-
Resistor color code calculator
Read 4, 5 and 6-band resistors: value, tolerance and the range a meter should show.
-
Voltage divider calculator
Output voltage, current and power of a two-resistor divider, with the R2 for a target voltage.
-
LED resistor calculator
The series resistor for one LED or a string, rounded to a stock value, with its power rating.
-
Parallel and series resistor calculator
Total resistance of two to six resistors in parallel and in series, with each one's current and power.
-
Ohm's law calculator
Enter any two of voltage, current, resistance and power to get the other two.
-
Resistor voltage drop calculator
The voltage across a resistor from the current, or from the supply and the rest of the circuit.
-
RC time constant calculator
τ = RC, the capacitor voltage at each time constant, and the filter cutoff.