Skip to content
Resistor Math

Resistor voltage drop calculator

Enter the resistor and the current flowing through it to see how many volts it takes up and how hot it runs. Add the supply voltage to see what is left for everything else. If you do not know the current, leave it empty and give the supply and the resistance of the rest of the circuit instead.

Like 100, 4.7k or 0.1.

Leave empty to work it out from the two boxes below.

Optional with a current; needed without one.

Only when the current is empty: the load's resistance.

Example: 2 V across 100 Ω

20 mA × 100 Ω = 2 V, turning 40 mW into heat. That leaves 3 V of the 5 V supply for the rest of the circuit.

Voltage drop 2 V
Current 20 mA
Power in the resistor 40 mW
Smallest common rating at 2× the power 1/8 W
Left for the rest of the circuit 3 V
Share of the supply 40%

Worked from the formula shown for low-voltage DC circuits. Part values vary within their tolerance, so confirm with a multimeter and the parts' datasheets before you rely on a figure.

The drop follows the current. If the rest of the circuit is a motor, LED, lamp or chip, its current changes with temperature and load, so the drop changes with it. Measure across the resistor with the circuit running to confirm.

The formula, with a worked example

What a voltage drop is

Current flowing through any resistance leaves a little less push on the far side. That difference in volts between the two ends of the part is its drop. In a single loop, the drops around the loop add up to the supply, so whatever one resistor takes is no longer available to the parts after it.

This is often exactly what you want. A resistor in front of an LED takes up the volts the LED does not need. A sense resistor turns a current into a small voltage that a meter or a microcontroller can read. In other places the drop is a loss, such as the resistance of a long thin wire starving a motor at the end of it.

Two ways to work it out

If you know the current, the answer is one multiplication. Measure the current with a meter in series, or take it from a datasheet, and multiply by the resistance. Adding the supply voltage is optional; it lets the calculator show what remains and the share of the supply the resistor uses.

If you only know the supply, you need the resistance of everything else in the loop. Add it to the resistor, divide the supply by the total to get the current, then multiply back. This is the same sum a voltage divider does, seen from the top resistor, and it only holds when the rest of the circuit behaves like a fixed resistance.

Sense resistors and shunts

Measuring current with a small resistor is common in battery monitors, motor drivers and chargers. The trick is choosing a value small enough not to rob the load of volts, yet large enough to give a readable signal. A 0.1 Ω part at 2 A gives 0.2 V, plenty for an amplifier or an analog input.

The drop is also the signal, so its accuracy follows the resistor tolerance. Current-sense parts are usually 1% or better and rated for the heat. Enter your shunt value and the highest current you expect to see both the signal size and the power it must shed.

Power and temperature

Every volt dropped at a given current becomes heat. The calculator shows the power in the resistor and the smallest common rating that gives it twice that headroom, the same margin used by the LED page. Parts run near their full rating get hot enough to discolour a board and drift in value.

Resistance itself shifts a little with temperature, by its temperature coefficient. For ordinary film parts the change is small, but a sense resistor that warms by fifty degrees can read a percent or so differently. Where precision matters, keep the dissipation low and pick a part with a low coefficient.

When the drop is not what you measured

A meter across the resistor shows the real drop with the circuit running. If it disagrees with the calculation, the current is usually not what you assumed. A battery sags under load, a regulator limits current, or a part in the loop changes its resistance as it warms, and any of these moves the current and so the drop.

Long leads and loose connections add resistance you did not count. Measure the drop across each part in turn and the figures should add up to the supply; a missing volt or two points to a joint or a wire. This calculator covers circuits up to 60 V DC, the range of batteries, bench supplies and hobby boards.

Voltage drop across common resistors

Resistor At 1 mA At 5 mA At 10 mA At 20 mA At 50 mA
10 Ω 0.01 V 0.05 V 0.1 V 0.2 V 0.5 V
22 Ω 0.022 V 0.11 V 0.22 V 0.44 V 1.1 V
47 Ω 0.047 V 0.235 V 0.47 V 0.94 V 2.35 V
100 Ω 0.1 V 0.5 V 1 V 2 V 5 V
220 Ω 0.22 V 1.1 V 2.2 V 4.4 V 11 V
470 Ω 0.47 V 2.35 V 4.7 V 9.4 V 23.5 V
1 kΩ 1 V 5 V 10 V 20 V 50 V

V = I × R. Doubling the current doubles the drop and multiplies the heat by four.

Frequently asked questions

How do I calculate the voltage drop across a resistor?

Multiply the current in amps by the resistance in ohms. 20 mA through 220 Ω is 0.02 × 220 = 4.4 V.

What is the voltage drop across a 1k resistor at 10 mA?

10 V, from 0.01 × 1,000. It also dissipates 0.1 W.

Does a resistor drop voltage if no current flows?

No. With zero current the drop is zero, which is why a resistor in an open circuit shows the full supply on both ends.

How do I find the current if I only know the supply?

Add the resistor to the resistance of the rest of the loop and divide the supply by that total. Then multiply by the resistor for its drop.

Why does the remaining voltage matter?

It is what the rest of the circuit actually receives. A chip that needs 3 V will not run if a resistor in front of it leaves only 2.5 V.

Is the voltage drop the same as the power loss?

No, but they are linked. The drop is in volts; multiply it by the current and you get the power lost as heat in watts.

Holding a tiny surface-mount resistor with a printed number instead of colour bands? Decode it with the SMD resistor code calculator.

Other calculators on this site